The acid dew point is the temperature at which sulfuric acid vapor in flue gas begins to condense, and it is much higher than the water dew point. When baghouse or duct wall temperatures fall below it, acid condenses and causes corrosion, and wet dust can stick to the filter bags and raise differential pressure.
1000 ÷ T = 2.276 − 0.0294·ln(PH₂O) − 0.0858·ln(PSO₃) + 0.0062·ln(PH₂O)·ln(PSO₃)T acid dew point (K), P partial pressure (mmHg) = volume fraction × flue gas absolute pressure (mmHg). Verhoff–Banchero correlation
This is a correlation for the sulfuric acid (SO₃·H₂O) dew point. Outside the experimental range it was fitted to, the error can grow, so designs should keep a temperature margin and confirm with measurements. The water dew point, the temperature at which water condenses at the same moisture partial pressure, is shown for reference.
Worked Example
Step
Calculation
Result
H₂O partial pressure
0.15 × 760
114.0 mmHg
SO₃ partial pressure
10 × 10⁻⁶ × 760
0.0076 mmHg
Sulfuric acid dew point
Verhoff–Banchero correlation
approx. 141°C
Water dew point
H₂O partial pressure 114.0 mmHg
approx. 54°C
Flue gas with 15 vol% moisture and 10 ppm SO₃ at 1 atm (101.3 kPa).
How Do You Manage the Acid Dew Point in a Baghouse?
Keep the operating temperature well above the acid dew point. Check the filter surface and the cold spots too, such as housing walls and hoppers.
Startup and shutdown are the riskiest periods. Wall temperatures easily drop below the acid dew point when hot flue gas enters a cold unit or when the unit is shut down.
Choose acid-resistant media. If acid gases are high and the unit runs near the dew point, check acid-resistant materials such as PPS, P84 and PTFE in the filter bag material selection chart.
Frequently Asked Questions
Is the acid dew point different from the dew point?
Yes. The dew point is the temperature at which water vapor condenses, while the acid dew point is the temperature at which acidic components such as sulfuric acid condense. Even a small amount of SO₃ raises the acid dew point far above the water dew point.
What if I don't know the SO₃ concentration?
You can estimate it from the SO₂ concentration and an SO₃ conversion rate. Conversion depends on the fuel and combustion conditions, so use measured or design values where possible.
Does this calculate the HCl dew point too?
No. This calculator covers only the sulfuric acid dew point. Hydrogen chloride (HCl) condenses at a lower temperature than sulfuric acid and requires a separate correlation.
Your results or checked items are added to the inquiry note automatically. Add your company and email, and our engineer will reply with a filter proposal.
Data collected: company name and email (plus any contact details you add) · Purpose: to review and respond to your inquiry · Retention: 5 years as an inquiry record, then deleted
✓
Thank you. We have received your request.
Head Office
Micro-one Co., Ltd. (head office and factory)
368 Yeongok-gil, Ipjang-myeon, Seobuk-gu, Cheonan-si, Chungcheongnam-do 31026, Republic of Korea Tel: +82-41-587-6911Fax: +82-41-587-6922Email: info@micro-one.kr
Dangjin Plant 2
1307 Tongjeong-ri, Seongmun-myeon, Dangjin-si, Chungcheongnam-do, Korea
Seoul Office
165 Gasan Digital 1-ro, Geumcheon-gu, Seoul (371-6, Gasan-dong)